The SX20C is a compact SWR-power meter. Featuring cross needle design for measuring SWR and output power simultaneously. Compact size makes it very useful for testing mobiles as well as base station installation.

Special Features:

• Cross needle design
• Rated from 3.5-30, 50-54, and 130-150 MHz
• Power ranges of 30 & 300 Watts

The SX40C is a compact SWR-power meter. Featuring cross needle design for measuring SWR and output power simultaneously. Compact size makes it very useful for testing mobiles as well as base station installation.

Special Features:
• Cross needle design
• Rated from 144-470 MHz
• Power ranges of 30 & 300 Watts

The Standard Horizon SCU-31 is a NMEA 0183 Smart Antenna that provides rapid acquisition time and NMEA output.

Can also be used as a replacement antenna for the older CP180 and CP300 chart plotters.

The KS-21 is the perfect antenna for small boats and RIBs. With only 100 cm length it guarantees the same performance of a 150 cm length VHF antenna. It’s built with a 1,4 mm thick fiberglass whip that gets fully foam injected with the special Scout 100% waterproof technique, and it’s ice white colored with high gloss anti-UV filter to prevent color deterioration.

The PA-3 is designed for deck or side mounting. It’s made of UV resistant reinforced nylon and allows the antenna to fold down in four ways with a quick release. 1” x 14 thread. Supplied with fitting set.

Innovative Komunica HF-PRO-2-PLUS-T portable Wide Spectrum antenna:

7 / 30MHz + 50MHz + 3.5MHz (via included coil) + VHF

Maximum robustness, super-light and ultra-compact size, measuring 29cm disassembled and 270cm maximum extension.

Ideal QRP, SOTA, etc. by telescopic tripod, magnetic base reinforced, etc (see Komunica accessories: TRIPOD-KIT & TRIPLE-MAG, etc).

Automatic antenna tuner specifically designed for IC-705

The Alex loop is a small and lightweight portable Loop Antenna for 7 to 30MHz, ideally suited for radio amateurs with space restrictions or for your vacation and hiking trip. The ultra lightweight loop is assembled without any tools within seconds and can be tuned with the supplied tuner to a perfect match. The internal S-Meter of your radio helps in tuning this antenna.

• Frequency range: 0.1 to 650 MHz
• Frequency entry: 1 kHz resolution
• Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600-Ohms systems
• SWR measurement range: 1 to 100 in numerical modes, 1 to 10 in chart modes
• R and X range: 0…2000, -2000…2000

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz.
A built-in ZOOM capability makes graphical measurements especially effective.
An integrated Time Domain Reflectometer mode can be used to locate a fault within the feedline system.

The following tasks are easily accomplished by using this analyzer:

• Rapid check-out of an antenna
• Tuning an antenna to resonance
• Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
• Making coaxial stubs or measuring their parameters
• Cable testing and fault location, measuring cable loss and characteristic impedance
• Measuring capacitance or inductance of reactive loads

• Frequency range: 0.1 to 1500 MHz
• Frequency entry: 1 kHz resolution
• Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600-Ohms systems
• SWR measurement range: 1 to 100 in numerical mode, 1 to 10 in graph mode
• R and X range: 0…2000, -2000…2000

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 60 kHz to 55 MHz.

A built-in ZOOM capability makes graphical measurements especially effective.

The following tasks are easily accomplished by using this analyzer:

• Rapid check-out of an antenna
• Tuning an antenna to resonance
• Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
• Making coaxial stubs or measuring their parameters
• Cable testing and fault location, measuring cable loss and characteristic impedance
• Measuring capacitance or inductance of reactive loads