The MBF-705 is a purposely designed desk top holder for the IC-705. The MBF-705 can position the IC-705 at slightly upright position to make operation easier.

The BC-202IP3L is a new multi-connectable rapid charger for Icom’s range of IP/LTE radios and selected Amateur radio products.
The BC-202IP3L charging pod can not only be used to charge one radio, it can also be connected to form a multi charger with a combination of 2, 3, 4, 5 or 6 pods. By simply sliding off the sides of each pod, you can slot them together in a daisy chain via pin connectors on each charger providing a strong, sturdy product.
The BC-202IP3L allows users to quickly charge the BP-271, BP-272 lithium-ion batteries and the forthcoming BP-307 large high capacity 7.2V / 3350mAh (typ.) li-Ion battery pack. 
The BC-202IP3L can be used with the IP100H, IP501H, IP503H, ID-31E (all versions), ID-51E (all versions), and the new Icom IC-705 QRP SDR transceiver.

The Alex loop is a small and lightweight portable Loop Antenna for 7 to 30MHz, ideally suited for radio amateurs with space restrictions or for your vacation and hiking trip. The ultra lightweight loop is assembled without any tools within seconds and can be tuned with the supplied tuner to a perfect match. The internal S-Meter of your radio helps in tuning this antenna.

PMR446 portable midland programmable from PC, easy to use and intended for semi-professional use and hunting. IPX4 waterproof protection. 99 PMR446 channels programmable also from PC to adapt it to your operational needs. Quick access to the RRM channel (Montana Radio Network). CTCSS and DCS subaudio tones, monitor function, key beep, battery saving function, Vox. Backlit LCD display, Scrambler function. High-performance speaker for excellent audio quality. Socket for external microphones or micro-earphones with double Jack with Kenwood pitch. Supplied with 2600 mA rechargeable Li-ion battery and desktop charger.

• Frequency range: 0.1 to 650 MHz
• Frequency entry: 1 kHz resolution
• Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600-Ohms systems
• SWR measurement range: 1 to 100 in numerical modes, 1 to 10 in chart modes
• R and X range: 0…2000, -2000…2000

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz.
A built-in ZOOM capability makes graphical measurements especially effective.
An integrated Time Domain Reflectometer mode can be used to locate a fault within the feedline system.

The following tasks are easily accomplished by using this analyzer:

• Rapid check-out of an antenna
• Tuning an antenna to resonance
• Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
• Making coaxial stubs or measuring their parameters
• Cable testing and fault location, measuring cable loss and characteristic impedance
• Measuring capacitance or inductance of reactive loads

• Frequency range: 0.1 to 1500 MHz
• Frequency entry: 1 kHz resolution
• Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600-Ohms systems
• SWR measurement range: 1 to 100 in numerical mode, 1 to 10 in graph mode
• R and X range: 0…2000, -2000…2000

The analyzer is designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 60 kHz to 55 MHz.

A built-in ZOOM capability makes graphical measurements especially effective.

The following tasks are easily accomplished by using this analyzer:

• Rapid check-out of an antenna
• Tuning an antenna to resonance
• Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
• Making coaxial stubs or measuring their parameters
• Cable testing and fault location, measuring cable loss and characteristic impedance
• Measuring capacitance or inductance of reactive loads

The analyzer is designed for measuring SWR (standing wave ratio), return loss, as well as other parameters of cable and antenna systems in the range of 100 kHz to 230 MHz.

It is the world’s first antenna analyzer capable of 16 hours of continuous measurements without battery recharging.

Small, handy and powerful vector network analyzer is designed for measuring most useful parameters of cable and antenna systems in the range of 100 kHz to 230 MHz. Compared with the other devices the Stick is the State-of-the-Art Antenna & Cable Analyzer. Because it has Key benefits: less size you obtain, less weight you carry, less time you measure.

The AA-35 ZOOM is a portable, self-calibrating analyzer, designed for measuring SWR (standing wave ratio), return loss, cable loss, as well as other parameters of cable and antenna systems in the range of 60 kHz to 35 MHz, with incredible ZOOM capability.

The following tasks are easily accomplished by using this analyzer:

• Rapid check-out of an antenna
• Tuning an antenna to resonance
• Comparing characteristics of an antenna before and after specific event (rain, hurricane, etc.)
• Making coaxial stubs or measuring their parameters
• Cable testing and fault location, measuring cable loss and characteristic impedance
• Measuring capacitance or inductance of reactive loads

• Frequency range: 0.1 to 2000 MHz
• Frequency entry: 1 kHz resolution
• Measurement for 25, 50, 75, 100, 150, 200, 300, 450 and 600-Ohm systems
• SWR measurement range: 1 to 100 in numerical modes, 1 to 10 in chart modes
• R and X range: 0…2000, -2000…2000